• Latest POSTS

    Engineering Drawing Online Test - Set 08

    Practice Test: Question Set - 08

    1. The ________ tool on the Dimension tool bar will place several dimensions at one time by using a selection box placed over several part features.
      (A) Linear
      (B) Continue
      (C) Baseline
      (D) Quick Dimension

    2. This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
      (A) Object
      (B) Hidden
      (C) Center
      (D) Phantom

    3. Referring to the fractional inches to decimal inches to millimeter conversion chart on page 55 what is the equivalent mm measurement of  3/16 inch.
      (A) 1.906
      (B) 4.7625
      (C) 5.958
      (D) 14.6844

    4. When using the descriptive geometry method to create an auxiliary view the drafter should _________.
      (A) Rotate the snap grid to the same angle of the inclined plane
      (B) Offset the right vertical line of the front view
      (C) Rotate the top line of the front view 45 degrees
      (D) Offset the top line of the front view 2 inches

    5. This type of solid has a polygon for a base and triangular lateral faces that intersect at a vertex:
      (A) Pyramid
      (B) Prism
      (C) Cone
      (D) Torus

    6. This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
      (A) Dimension line
      (B) Extension line
      (C) Leader
      (D) Specification

    7. Several of the tools used in traditional drafting include the following:
      (A) Parallel straight edge
      (B) 45 degree triangle
      (C) Circle template
      (D) All of the above

    8. The top, front, and bottom views align in this manner:
      (A) Horizontally
      (B) Vertically
      (C) According to the planar views
      (D) Parallel to the frontal plane

    9. The principle reason for using an auxiliary view is ________.
      (A) To eliminate hidden lines
      (B) To create a true projection plane from an inclined plane in one of the primary views
      (C) To show cylinders as ellipses
      (D) To locate center marks

    10. A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
      (A) Client
      (B) CAD trainee
      (C) Receptionist
      (D) Checker

    11. The ________ dimension tool will place the length of an angled line.
      (A) Aligned
      (B) Angle
      (C) Linear
      (D) Radial

    12. Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for_________.
      (A) Circle templates
      (B) Triangles
      (C) Technical pens
      (D) Lettering guides

    13. This type of surface is tipped to all principal planes of projection and does not appear true size in any standard view:
      (A) Foreshortened
      (B) Parallel
      (C) Orthographic
      (D) Oblique

    14. A partial auxiliary view usually shows only features on the _________ of the inclined line and not any projection of other planes.
      (A) Hidden lines
      (B) Plane
      (C) Center lines
      (D) None of the above

    15. An architect often relies on a _________ to complete the set of technical drawings used in the design of an office building.
      (A) Technical illustrator
      (B) Artist
      (C) Drafter
      (D) Construction superintendent

    Show and hide multiple DIV using JavaScript View All Answers

    • Blogger Comments
    • Facebook Comments

    Post a Comment

    Item Reviewed: Engineering Drawing Online Test - Set 08 Rating: 5 Reviewed By: Pranab Debnath
    Scroll to Top