Strength of Materials MCQ Practice Test

Practice Test: Question Set - 31

1. A closely coiled helical spring is of mean diameter (D) and spring wire diameter (d). The spring index is the ratio of
    (A) 1/d
    (B) 1/D
    (C) D/d
    (D) d/D

2. The compression test is carried on __________ materials.
    (A) Ductile
    (B) Brittle
    (C) Malleable
    (D) Plastic

3. If the tearing efficiency of a riveted joint is 50%, then ratio of rivet hole diameter to the pitch of rivets is
    (A) 0.20
    (B) 0.30
    (C) 0.50
    (D) 0.60

4. The breaking stress is __________ the ultimate stress.
    (A) Equal to
    (B) Less than
    (C) Greater than
    (D) None of these

5. The section modulus (Z) of a beam is given by
    (A) I/y
    (B) I.y
    (C) y/I
    (D) M/I

6. The Rankine's formula holds good for
    (A) Short columns
    (B) Long columns
    (C) Both short and long columns
    (D) Weak columns

7. When two main plates are kept in alignment butting each other and riveted with cover plate on both sides of the main plates with two rows of rivets in each main plate, the joint is known as ________ double cover butt joint.
    (A) Single riveted
    (B) Double riveted
    (C) Multi riveted
    (D) None of these

8. When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under
    (A) Tensile stress
    (B) Compressive stress
    (C) Shear stress
    (D) Bending stress

9. The maximum bending moment of a simply supported beam of span l and carrying a point load W at the center of beam, is
    (A) Wl/4
    (B) Wl/2
    (C) Wl
    (D) Wl²/4

10. A tensile test is performed on a mild steel round bar. Its diameter after fracture will
    (A) Remain same
    (B) Increase
    (C) Decrease
    (D) Depend upon rate of loading

11. Transverse fillet welds are designed for
    (A) Tensile strength
    (B) Compressive strength
    (C) Shear strength
    (D) Bending strength

12. The product of the tangential force acting on the shaft and its distance from the axis of the shaft (i.e. radius of shaft) is known as
    (A) Bending moment
    (B) Twisting moment
    (C) Torsional rigidity
    (D) Flexural rigidity

13. The unit of strain is
    (A) N-mm
    (B) N/mm
    (C) mm
    (D) No unit

14. In spring balances, the spring is used
    (A) To apply forces
    (B) To measure forces
    (C) To absorb shocks
    (D) To store strain energy

15. A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum shear stress will be
    (A) 400 MPa
    (B) 500 MPa
    (C) 900 MPa
    (D) 1400 MPa

Show and hide multiple DIV using JavaScript View All Answers

Strength of Materials:
  Set 01      Set 02      Set 03      Set 04      Set 05      Set 06      Set 07      Set 08      Set 09
  Set 10      Set 11      Set 12      Set 13      Set 14      Set 15      Set 16      Set 17      Set 18
  Set 19      Set 20      Set 21      Set 22      Set 23      Set 24      Set 25      Set 26      Set 27
  Set 28      Set 29      Set 30      Set 31
  • Blogger Comments
  • Facebook Comments


Post a Comment

Item Reviewed: Strength of Materials MCQ Practice Test Rating: 5 Reviewed By: Pranab Debnath
Scroll to Top