Theory of Machines On-line Test - Set 25

Practice Test: Question Set - 25

1. The inversion of a mechanism is
    (A) Changing of a higher pair to a lower pair
    (B) Turning its upside down
    (C) Obtained by fixing different links in a kinematic chain
    (D) Obtained by reversing the input and output motion

2. The static balancing is satisfactory for low speed rotors but with increasing speeds, dynamic balancing becomes necessary. This is because, the
    (A) Unbalanced couples are caused only at higher speeds
    (B) Unbalanced forces are not dangerous at higher speeds
    (C) Effects of unbalances are proportional to the square of the speed
    (D) Effects of unbalances are directly proportional to the speed

3. In gramophones for adjusting the speed of the turntable, the following type of governor is commonly employed
    (A) Hartung governor
    (B) Wilson Hartnell governor
    (C) Pickering governor
    (D) Inertia governor

4. For a kinematic chain to be considered as mechanism
    (A) Two links should be fixed
    (B) One link should be fixed
    (C) None of the links should be fixed
    (D) There is no such criterion

5. Which of the following would constitute a link?
    (A) Piston, piston rod and cross head
    (B) Piston and piston rod
    (C) Piston rod and cross head
    (D) Piston, crank pin and crank shaft

6. Which of the following is a spring controlled governor?
    (A) Hartnell governor
    (B) Hartung governor
    (C) Wilson-Hartnell governor
    (D) All of these

7. The frictional torque transmitted in a flat collar bearing, considering uniform wear, is (where r₁ and r₂ = External and internal radii of collar respectively)
    (A) (1/2) μ W (r₁ + r₂)
    (B) (2/3) μ W (r₁ + r₂)
    (C) (1/2) μ W [(r₁³ - r₂³)/(r₁² - r₂²)]
    (D) (2/3) μ W [(r₁³ - r₂³)/(r₁² - r₂²)]

8. The velocity of sliding __________ the distance of the point of contact from the pitch point.
    (A) Is directly proportional to
    (B) Is inversely proportional to
    (C) Is equal to cosφ multiplied by
    (D) Does not depend upon

9. A spring controlled governor is said to be isochronous when the controlling force
    (A) Increases as the radius of rotation decreases
    (B) Increases as the radius of rotation increases
    (C) Decreases as the radius of rotation increases
    (D) Remain constant for all radii of rotation

10. The factor which affects the critical speed of a shaft is
    (A) Diameter of disc
    (B) Span of shaft
    (C) Eccentricity
    (D) All of these

11. When the sleeve of a Porter governor moves upwards, the governor speed
    (A) Increases
    (B) Decreases
    (C) Remain unaffected
    (D) First increases and then decreases

12. It is required to connect two parallel shafts, the distance between whose axes is small and variable. The shafts are coupled by
    (A) Universal joint
    (B) Knuckle joint
    (C) Oldham's coupling
    (D) Flexible coupling

13. In S.H.M., acceleration is proportional to
    (A) Velocity
    (B) Displacement
    (C) Rate of change of velocity
    (D) All of the above

14. The velocity of a particle moving with simple harmonic motion, at any instant is given by (where ω = Displacement of the particle from mean position)
    (A) ω √(x² - r²)
    (B) ω √(r² - x²)
    (C) ω² √(x² - r²)
    (D) ω² √(r² - x²)

15. The lead screw of a lathe with nut forms a
    (A) Rolling pair
    (B) Sliding pair
    (C) Screw pair
    (D) Turning pair

Show and hide multiple DIV using JavaScript View All Answers

Theory of Machines:
  Set 01      Set 02      Set 03      Set 04      Set 05      Set 06      Set 07      Set 08      Set 09
  Set 10      Set 11      Set 12      Set 13      Set 14      Set 15      Set 16      Set 17      Set 18
  Set 19      Set 20      Set 21      Set 22      Set 23      Set 24      Set 25      Set 26      Set 27
  Set 28      Set 29      Set 30      Set 31      Set 32      Set 33      Set 34      Set 35      Set 36
  Set 37      Set 38
  • Blogger Comments
  • Facebook Comments


Post a Comment

Item Reviewed: Theory of Machines On-line Test - Set 25 Rating: 5 Reviewed By: Pranab Debnath
Scroll to Top