Today, all competitive exams are Multiple Choice Questions(MCQ) based examination system and the main factor is to answer each question in a prescribed time. So, practice as much as possible before the original test you are going to face.
Total number of Multiple Choice Question (MCQ) is 15 and time allotted for each question is 30 seconds. After the allotted time, the question will be marked as un-attempt.
QUIZ
Test Conducted by: ObjectiveBooks.com
Next Mock Tests:
01. Selection of the routes, of highways depends upon
(A) Feasibility of attaining ruling gradient
(B) Avoidance of cutting hard rocks
(C) Minimum number of bridges
(D) All the above
Answer: Option D
02. For a simply supported beam carrying uniformly distributed load W on it entire length L, the maximum bending moment is
(A) WL/4
(B) WL/8
(C) WL/2
(D) WL/3
Answer: Option B
03. Joints in concrete structures, are provided
(A) To reduce the tensile stresses likely to be developed due to evaporation of water
(B) To minimise the change in the dimensions of the slab
(C) To minimise the necessary cracking
(D) All the above
Answer: Option D
04. The real image of an object formed by the objective must lie
(A) In the plane of cross hairs
(B) At the centre of the telescope
(C) At the optical centre of the eye-piece
(D) Anywhere inside the telescope
Answer: Option A
05. The final selection of a construction site, is done by
(A) Departmental representative or user
(B) Local civil authority representative
(C) Representative of engineer authority
(D) All the above
Answer: Option D
06. Portland pozzolana cement possesses
(A) Higher resistance to chemical attack
(B) Lower heat of hydration
(C) Lower shrinkage on drying
(D) All the above
Answer: Option D
07. The sewage treatment in septic tanks is due to
(A) Anaerobic decomposition
(B) Aerobic decomposition
(C) Parasitic decomposition
(D) None of these
Answer: Option A
08. If the rate of change of grade permitted along a vertical curve is r and total change of grade is g%, the length L of the curve to be provided, is
(A) L = (r × 100/g) m
(B) L = (g × 100/r) m
(C) L = (r + g) × 100 m
(D) L = [100/(r + g)] m
Answer: Option B
09. Curing
(A) Reduces the shrinkage of concrete
(B) Preserves the properties of concrete
(C) Prevents the loss of water by evaporation
(D) All of the above
Answer: Option D
10. On Indian Railways standard length of rails for M.G. track, is
(A) 33 ft (10.06 m)
(B) 36 ft (10.97 m)
(C) 39 ft (11.89 m)
(D) 42 ft (12.8 m)
Answer: Option C
11. The angle of intersection of a curve is the angle between
(A) Back tangent and forward tangent
(B) Prolongation of back tangent and forward tangent
(C) Forward tangent and long chord
(D) Back tangent and long chord
Answer: Option A
12. The velocity of drainage water in the barrels of a syphon-aqueduct, is normally limited to
(A) 1 to 2 m per second
(B) 2 to 3 m per second
(C) 3 to 4 m per second
(D) 4 to 5 m per second
Answer: Option B
13. The process in which the chlorination is done beyond the break point is known as
(A) Pre-chlorination
(B) Post chlorination
(C) Super chlorination
(D) Break point chlorination
Answer: Option C
14. If the furnace is provided with insufficient fuel at low temperatures, the type of pig iron produced, is called
(A) Bessemer pig
(B) Grey or foundry pig
(C) White or forge pig
(D) Mottled pig
Answer: Option C
15. Bessemer process is used for the manufacture of
(A) Pig iron
(B) Cast iron
(C) Wrought iron
(D) Steel
Answer: Option D