Today, all competitive exams are Multiple Choice Questions(MCQ) based examination system and the main factor is to answer each question in a prescribed time. So, practice as much as possible before the original test you are going to face.
Total number of Multiple Choice Question (MCQ) is 15 and time allotted for each question is 30 seconds. After the allotted time, the question will be marked as un-attempt.
QUIZ
Test Conducted by: ObjectiveBooks.com
Next Mock Tests:
01. In sewers designed with self cleansing velocity,
(A) The bottom is silted
(B) The bottom is scoured
(C) Both silting and scouring occur at the bottom
(D) Neither silting nor scouring occurs at the bottom
Answer: Option D
02. For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be
(A) 600 mm
(B) 750 mm
(C) 900 mm
(D) More than 1 m
Answer: Option B
03. The type of valve which allows water to flow in one direction but prevents its flow in the reverse direction is
(A) Reflux valve
(B) Sluice valve
(C) Air relief valve
(D) Pressure relief valve
Answer: Option A
04. For preparing porcelains, the clay should be
(A) Sufficiently pure
(B) Of high degree of tenacity
(C) Of good plasticity
(D) All the above
Answer: Option D
05. Minimum spacing between horizontal parallel reinforcement of the same size should not be less than
(A) One diameter
(B) 2.5 diameters
(C) 3 diameters
(D) 3.5 diameters
Answer: Option A
06. Non-uniform compaction may cause the concrete
(A) Porous
(B) Non-homogeneous
(C) Reduced strength
(D) All the above
Answer: Option D
07. The portion of a brick cut to form angles other than right angles in plan, is known as
(A) Queen closer
(B) King closer
(C) Closer
(D) Squint brick
Answer: Option D
08. You are asked to construct a massive dam, the type of cement you will use, is
(A) Ordinary Portland cement
(B) Rapid hardening cement
(C) Low heat cement
(D) Blast furnace slag cement
Answer: Option C
09. Minimum length of a transition curve required for
(A) 2° curves for a maximum permissible speed of 135 km/hr, is 220 metres
(B) 4° curves for a maximum permissible speed of 95 km/hr, is 220 metres
(C) 6° curves for a maximum permissible speed of 80 km/hr, is 220 metres
(D) All the above
Answer: Option D
10. The basic wind speed is specified at a height 'h' above mean ground level in an open terrain. The value of 'h' is
(A) 10 m
(B) 20 m
(C) 25 m
(D) 50 m
Answer: Option A
11. Ranging in chain survey means
(A) Looking at an isolated point not on the line
(B) Establishing an intermediate point on the line
(C) Determining the distance between end points
(D) Determining the offset distance
Answer: Option B
12. The bending moment is maximum on a section where shearing force
(A) Is maximum
(B) Is minimum
(C) Is equal
(D) Changes sign
Answer: Option D
13. The radius of curvature provided along a transition curve, is
(A) Minimum at the beginning
(B) Same throughout its length
(C) Equal to the radius of circular curve
(D) Varying from infinity to the radius of circular curve
Answer: Option D
14. Prof. Running suggested the method for extending the discharge curve. It is known as
(A) Logarithmic method
(B) √y method
(C) General method
(D) None of these
Answer: Option A
15. The Random errors tend to accumulate proportionally to
(A) Numbers of operations involved
(B) Reciprocal of operations involved
(C) Square root of the number of operation involved
(D) Cube root of the number of operation involved
Answer: Option C
