SSC Chemical Engineering Mock Test Series - Set 10

Chemical Engineering Mock Test - Set 10

---

Today, all competitive exams are Multiple Choice Questions(MCQ) based examination system and the main factor is to answer each question in a prescribed time. So, practice as much as possible before the original test you are going to face.

Total number of Multiple Choice Question (MCQ) is 15 and time allotted for each question is 30 seconds. After the allotted time, the question will be marked as un-attempt.

Test Conducted by: ObjectiveBooks.com

---

 Next Mock Tests:

Set 01

Set 02

Set 03

Set 04

Set 05

Set 06

Set 07

Set 08

Set 09

Set 10

Set 11

Set 12

---

View Test Result:

01. The radioactive isotope of hydrogen is
     (A) Deuterium
     (B) Tritium
     (C) Protium
     (D) None of these
     Answer: Option B

02. Cast iron has the unique property of high
     (A) Ductility
     (B) Damping characteristics
     (C) Hardness
     (D) Malleability
     Answer: Option B

03. Sulphur is melted in the sulphuric acid plant most commonly by employing
     (A) Electrical heater
     (B) Steam heater
     (C) Direct fuel oil fired heater
     (D) Gas fired furnace
     Answer: Option B

04. Out of the following, __________ pipe is the least corrosion resistant.
     (A) Mild steel
     (B) Copper
     (C) Wrought iron
     (D) Stainless steel
     Answer: Option C

05. Which of the following is a synthetic abrasive?
     (A) Corundum
     (B) Emery
     (C) Pumice
     (D) Silicon carbide
     Answer: Option D

06. __________ strain gauge is the most sensitive sensing element for strain measurement.
     (A) Photo-elastic
     (B) Semiconductor
     (C) Wire resistance
     (D) None of these
     Answer: Option B

07. Titanium alloys are welded using the Following process:
     (A) TIG welding
     (B) Submerged arc welding
     (C) Butt welding
     (D) Electron beam welding
     Answer: Option A

08. The main purpose of providing stepping on the trays is to
     (A) Increase the residence time
     (B) Decrease the pressure drop
     (C) Facilitate handling of large flow rate of liquid
     (D) Improve the flow condition
     Answer: Option C

09. Oxygen carrying pipelines in chemical industries are coloured with __________ colour.
     (A) Yellow
     (B) Black
     (C) Blue
     (D) Red
     Answer: Option C

10. Two iron pipes of the same nominal diameter but different schedule numbers will have the same
     (A) Inside diameter
     (B) Outside diameter
     (C) Wall thickness
     (D) None of these
     Answer: Option A

11. Annealing of a material does not
     (A) Permit its further cold working
     (B) Soften it
     (C) Case harden it
     (D) None of these
     Answer: Option C

12. __________ forces do not act in case of fluids.
     (A) Vibratory
     (B) Centrifugal
     (C) Elastic
     (D) Tensile
     Answer: Option D

13. RADAR is
     (A) Acronym for Radio Detection and Ranging
     (B) Name of technique for locating distant objects
     (C) Name of instrument for locating distant objects
     (D) All (a), (b) & (c)
     Answer: Option D

14. Statistical quality control was developed by __________, an American scientist during world war-II.
     (A) Walter shewhart
     (B) Fredric Taylor
     (C) John Wright
     (D) Woolmer
     Answer: Option A

15. Three elastic constants for a completely anisotropic elastic material which follows the Hooke's law are young's modulus, elastic limit stress and yield stress. Which of the following properties is most sensitive to increase in strain rate?
     (A) Tensile strength
     (B) Elastic limit
     (C) Proportional limit
     (D) Yield strength
     Answer: Option C

---